Since your 2007 Damon Daybreak 3276 Class A Motorhome was built on a Workhorse chassis with a GVWR of 20,500lbs you'll have a few options depending on whether or not you have an R-series or W-series Workhorse chassis:
For the R-Series you'll need the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes # RM88RR.
For the W-Series there's a further breakdown of the chassis types. For W16 and W18 you'll need the Roadmaster Exact Center Steering Stabilizer... view full answer...
It sounds like the wiring was changed going into the solenoids at the hydraulic pump on your 2007 Damon Daybreak. I would check these connectors as it sounds like they were mixed up if the unit was swapped out. This would explain why your jack positions are all off and why the auto level fails when you try to use it. The system sends power to one jack and when a different jack lifts the camper the internal sensors read an error. view full answer...
The Bauer Products Motorhome Door Lock # BA64FR that you referenced could fit your 2006 Damon Challenger 348F but you would have to open up the cut out dimensions a little bit as this is designed to fit the dimensions of 5-1/4" wide x 4-1/2" tall, view full answer...
The Kwikee Electric RV Step Complete Assembly - Triple - 23 Series - 24" Wide Item # LC3694042 are the closest to your current mounting bracket dimensions of 16" x 28". This kit comes with everything you need to automatically open and close your steps. view full answer...
Since your 2006 Damon Daybreak 3276 is built on a Ford chassis with a 20,500 lb GVWR the correct rear sway bar is the part # RM-1139-143. This will do a really good job getting rid of the sway and keeping the motorhome on the road without requiring over corrections.
To help with the bumps and also improve handling the SumoSprings part # SSF-171-40-2 would be what you'd want for the front and then # SSR-187-54-1 for the rear. view full answer...
I do have an option for you but the Advent Air RV Air Conditioners like part # ACM135 or part # ACM150 when using the Carrier Adapter Wiring Kit for Advent Air RV Air Conditioners part # ACCARKIT isn't compatible with models that have a heat pump. The only option we can offer would be to replace the Carrier distribution box with the Air Distribution Box part # ACDB and then add the Electric Heat Strip for Advent Air RV Air Conditioners part # ACMHD. view full answer...
The Advent Air Rooftop RV Air Conditioner part # ACM135 for 13,500 Btu's or part # ACM150 for 15,000 Btu's are both available and ready for purchase. The Coleman Adapter Kit part # ACCOLKIT that you referenced is for Coleman units so it will not be needed to replace your Carrier. However, both of the above kits come with everything that is needed anyhow. The adapter kit is more or less to retain your wall thermostat which you said you do not have. There are no Advent to Carrier adapter... view full answer...
The thermostat and remote of the Atwood Air Command Rooftop RV Air Conditioner w/ Heat Pump # AT15033-22 does come with ability to control a furnace like you need. You will be able to wire in your furnace's control wiring to the furnace so that it can be controlled. view full answer...
The correct replacement for your Carrier Air V would be the Advent Air Replacement RV Air Conditioner for Carrier Setup w/ Start Capacitor # ACCAR135 for 13,500 BTU's and # ACCAR150 for 15,000 BTU's. This AC unit replaces the Carrier air conditioner on your RV or camper. Included adapter wiring kit enables the AC to work with your existing Carrier setup. view full answer...
According to the code you provided you would have a 39 series step so the Kwikee Electric RV Step Complete Assembly # LC3724742 would be the correct replacement. The exact replacement for this specific model was discontinued so you'll notice that the dimensions are slightly off (about 1/4") but this is going to be the closest option.
In my experience it's best to replace the door sensor when you swap out the steps since the it always seems be the cause of any malfunctions after steps... view full answer...
We have the kit part # 3442703414KIT which comes with everything needed to install roof membrane like the # 3441700534142711435. The kit includes a 2-gallon container of EXP90 adhesive, six 10-oz cartridges (300 linear feet) of XTRM 100 self-leveling sealant, and two rolls of butyl tape. view full answer...
The Furrion Chill HE RV Air Conditioner System # FR85PV can replace your Coleman unit, but most Coleman's have a 9-pin connector so you'll need to pick up an adapter # ACCOLKIT in order to plug your new wire harness into the old controller. The opening size for AC units is standard at 14" x 14". view full answer...
The correct replacement for your 300-1406 motor is the Replacement Motor for Lippert Electric Coach Step part # LC301695. If you need other components I would need more info on the steps as this specific motor fits quite a few different steps. If it's a Kwikee 25 Series most likely you just need the part # LC369354 for the gear. view full answer...
Try resetting the Carrier internal computer by disconnecting the 12 volt power source for a 1-1/2 minutes. This may clear the computer from what caused it to quit working correctly. Many users report that the AC will then work for some amount of time until the existing problem that caused the computer to say STOP happens again. With all power off, you can remove the rooftop shroud and ensure that parts are clean up there, especially the coils. Over heating due to dirty coils could be... view full answer...
The Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger # PD9280A DC terminals use a 5/32” hex bit # PT79VV to secure the wire. You'll want to ensure that you don't exceed 50 in-lbs. torque on the output terminals when you're tightening them down. view full answer...
Assuming your clearance lights are surface-mounted, we do have an option for 2-1/2 inch round, 2-wire amber clearance lights:
- Optronics LED Clearance or Side Marker Trailer Light w/ Reflector - 1 Diode - Round - Amber Lens # MCL0040ABB
These are typically used on trailers, but they do have just the ground and power wire running from them, so you can use them as replacements since yours have the same wiring. I have added a link below to a video review for you to check out as well if... view full answer...
We do indeed have just the heating element and wiring kits for Hott Rod Water Heaters available as separate parts. If you have a 6-gallon tank you will use part # DGR6P2PB for the element and for a 10 gallon tank we have part # DGR6P10PB.
The correct wiring kit for either option is the Diamond # DGSK1VP view full answer...
The overall outside diameter of the Brophy Rope Ring Tie-Down Anchor # RR09 referenced in your question is exactly 3-7/8 inches. I have attached a diagram to assist. view full answer...